In addition to operating systems supported for the application, the license server will run on the Windows Server 2008, Windows Server 2008 R2, Windows Server 2003, and Windows 2003 R2 Server Editions.Primary login on workstations may be Netware or Windows. Either Microsoft® or Novell TCP/IP protocol stacks are acceptable.The license server and all workstations that will run applications dependent on network licensing must run TCP/IP protocol.Intel Pentium 4 with Intel EM64T support with SSE2 technology.Intel® Xeon® with Intel EM64T support with SSE2 technology.Windows XP: Intel® Pentium® 4 or AMD Athlon™ Dual Core, 1.6 GHz or Higher with SSE2 technology.Windows 8 and Windows 7: Intel Pentium 4 or AMD Athlon Dual Core, 3.0 GHz or Higher with SSE2 technology.1280 x 1024 True Color video display adapter 128 MB or greater, Pixel Shader 3.0 or greater, Direct3D®-capable workstation class graphics card.6 GB free hard disk available not including installation requirements.
We do not recommend or support the use of onboard graphics found with some PC configurations. OpenCL is required for Mastercam to be able to hand off certain computation tasks to the graphics card to increase system performance.
Intel Pentium 4 processor or AMD Athlon, 3.0 GHz or higher or Intel or AMD Dual Core processor, 2.0 GHz or higher Other graphics cards can be used, but they must offer full OpenGL 3.2 and OpenCL 1.2 support.
Side-by-side install Supported (for example AutoCAD 2013 and AutoCAD 2014 on the same system)Īdditional requirements for large datasets, point clouds and 3D modeling Supports Windows display adapter capable of 1024x768 with True Color capabilities Disk space Windows XP Home (Service Pack 3 or later)ġ024x768 (1600x1050 or higher recommended) with True Color Windows XP Professional (Service Pack 2 or later) VBA is not supported on Windows XP Professional It may be necessary to have a second parallel port dedicated specifically to the hardware lock.Windows XP Professional (Service Pack 3 or later) Other printing conflicts may occur while printing through the same port as the hardware lock.
Certain devices may cause hardware lock failure, which will render the software useless until the lock is replaced. If you are using parallel port hardware locks instead of USB hardware locks, it is not suggested to have a printer, ZIP disk, scanner or any other device connected to the same port as your AutoNest hardware lock. If you have Router-CIM 2007 or newer, the hardware locks are compatible and no switch is necessary. If you fail to return the old lock, you will be invoiced for the full purchase price of the software. Lost locks are the customer’s responsibility so insure your shipment for full software value. If you are upgrading from a version prior to 2007, you will receive a new Hardware Lock with the 2016 software and will have to return the old Hardware Lock through a traceable carrier. Disk Space: 6 GB free hard disk available not including installation requirements. The Router-CIM 2007-2016 Hardware Locks are different than the 2004, 2005, and 2006 Hardware Locks. Display Card: True color video display adapter 128 MB or greater, Pixel Shader 3.0 or greater, Direct3D capable workstation class graphics card. For the parallel port type, only one port is necessary since these locks can plug into each other. Since there are two hardware locks required if you are using the nest software, you should have two USB ports available. Additional requirements for 3D Modeling CPU Type: Intel Pentium 4 processor or AMD Athlon, 3.0 GHz or greater or Intel or AMD Dual Core processor, 2.0 GHz or greater: Memory: 32-bit: 4 GB RAM 64-bit: 8 GB RAM or more. These can be either a USB type or a Parallel Port (printer port) type. Graphics Card: Dedicated GPU Card: Nvidia GTX 560 or Above: Screen Resolution: 1366. In addition to the hardware requirements listed above, it is important to note that Router-CIM and AutoNEST require hardware locks (often called 'dongles') in order to function. Autodesk AutoCAD 2015 System Requirements. You should check your hardware against the Autodesk Certified Hardware List to be sure of compatibility with your version of AutoCAD.Ĭlick here to check Autodesk Certified Hardware List
Router-CIM 2016 supports the following Autodesk products:Īdditionally, we provide an Inventor Link to the following versions of Autodesk Inventor: